## BenQ-Siemens Secret Codes

BenQ-Siemens Secret Codes
Software version:
*#06#
to see more info, press softkey again

English menu:
*#0001#

Deutsch menu:
*#0049#

Secret Code:
*#0606# remove sim card before

Unlock Sim:
*#0003*(secret code)#

Bonus Screen:
*12022243121

Factory settings: Type *#9999# to reset factory settings.(not tested).


==================

iemens CODES
Siemens
MODELS

CODES & DESCRIPTIONS

*#0003*(secret code 8 digits)# All Siemens Phones: Service Provider Unlock
Siemens S25/C25
SP unlock *#0003*(secret code 8 digits)#
Show IMEI code: * # 06 #
Resets language to automatic selection : * # 0000 # then Green button


Pin Out
Data Cable schematics
Phone’s connector pin-out:
1- GND
2- SB
3- POWER
4- NC
5- TX
6- RX
7- CLOCK
8- DATA
9- GND MIC
10- HF MIC
11- AUDIO
12- GND AUDIO
Siemens S1/S3/S3 Com
To view the software date and else with S3 com, S4, S4Power, Sony cmdx 1000e press with SIM removed *#06# and left softkey.

To view some other stuff with S4Power, Sony cmdx 1000e press with SIM removed *#06# and left softkey twice.

To view the software date with S3 com, S4, S4Power, Sony cmdx 1000e press with SIM installed menu 98 and left softkey twice.

ACTIVATE MONITOR MODE
Siemens S1/S3

Menu, 9 (Phone Options), 7 (Phone Status), Left Display Button (left MENU key), 5553756, Hang-Up Button (Red Handset key)
Siemens S3 COM/S4

Menu, 9 (Phone Options), 7 (Phone Status - 8 on Some), Left Display Button (left MENU key), 7684666, Hang-Up Button (Red Handset key)

Note: Now Monitor should appear at the bottom of the Network Options menu.
MONITOR MODE
Pressing the right Display Button when in monitor mode will toggle into 1 and 2 modes

Pressing the right Display Button when in monitor mode will show a list of the six cells with the strongest signals.

Test Mode Indicators: (* = only available when call in progress )
CH Channel Number

RX Signal Strength (dB)

N NCC (Colour Code)

B BCC (Colour Code)

CI Cell ID (in Hex)

C1+ How long before phone does forced hand over. (see RX and RXAM)

LAI Location Area Identity. Display Network ID code (42F010 = 240.01) and MSC

TXPWR Transmit Power (dB)

RXAM Receive signal strength cut-off point

TS* Time Slot Number

TA* Timing Advance. Distance from tower in Km X 2

PL* Power Level
POWER table
PL: 5 6 7 8 9 10 11 12 13 14 15

dB: 33 31 29 27 25 23 21 19 17 15 13

Watts: 2 1.3 .8 .5 .3 .2 .13 .08 .05 .03 .02
LF* C1 value with continuous transmission from tower

LS* C1 Value with discontinuous transmission from tower

QF* Bit Error Rate with continuous transmission from tower

QS* Bit Error Rate with discontinuous transmission from tower
BER (bit error rate) table
QF/QS register: 0 1 2 3 4 5 6 7

% of bit sent: 0.2 0.8 0.4 1.6 3.2 6.4 12.8 25.6
Siemens S1/S3
Here’s a trick to play Tetris, also known as Klotz on a Siemens S1.
Turn the phone on. Enter PIN. Before the telephone has logged in to the your GSM net do the following steps.
1: Choose F 9 (function settings)
2: Choose send own number and push the right button for choose.
3: Push 9
USE 2 as <> , rotate the klotz with 5 and drop with 4.
[I have just heard from one of the programmers of the phone that Tetris was in the phone during development, but it was removed before it was produced. Apparently someone has the patent on games in mobile phones and Siemens didn’t want to pay the licensing fees. It was either in Menu F-9-9 or it’s not there at all.]
Siemens S3 Comfort

MONITOR MODE

The Siemens S3 Com series have a Monitor mode that can be activated directly from the standard user keypad. In order to activate this mode, you must enter the special access code currently programmed into the phone.
TO ACTIVATE MONITOR MODE:
Turn the phone on.
Enter the PIN access code on press OK. (Only if is enabled).
Press Menu. (Left top button).
Press 9. (Phone Options).
Press 8. (Phone Status) (May be button 7 in some phones).
You may see your IMEI Number
Left Display Button (Top left MENU key).
7684666
Hang-Up Button. (Red Handset key).

Note: Monitor should appear now at the bottom of the Network Options menu.
MONITOR MODE

Pressing the right Display Button when in monitor mode will toggle into 1 and 2 modes
Siemens S4/S4 Power
In phonebook under “Own Phone No.” enter +12022243121 (which is the number to the White House) and you’ll get a greeting from the people who programmed the phone.

MONITOR MODE

The Siemens S4 series have a Monitor mode that can be activated directly from the standard user keypad. In order to activate this mode, you must enter the special access code currently programmed into the phone.
TO ACTIVATE MONITOR MODE:
Menu, 9 (Phone Options), 7 (Phone Status), Left Display Button (left MENU key), 7684666, Hang-Up Button (Red Handset key)
Now “Monitor” should appear at the bottom of the Network Options menu.
Pressing the right Display Button when in monitor mode will show a list of the six cells with the strongest signals.

Test Mode Indicators: (* = only available when call in progress )
——————–
CH Channel Number

RX Signal Strength (dB)
N NCC (Color Code)
B BCC (Color Code)
CI Cell ID (in Hex)
C1+ how long before phone does forced hand over. (see RX and RXAM)
LAI Location Area Identity. Display Network ID code (42F010 = 240.01) and MSC
TXPWR Transmit Power (dB)
RXAM Reeceive signal strength cut-off point
TS* Time Slot Number
TA* Timing Advance. Distance from tower in Km X 2
PL* Power Level

Power Table

PL: 5 6 7 8 9 10 11 12 13 14 15
dB: 33 31 29 27 25 23 21 19 17 15 13
Watts: 2 1.3 .8 .5 .3 .2 .13 .08 .05 .03 .02

LF* C1 value with continuous transmission from tower
LS* C1 Value with discontinuous transmission from tower
QF* Bit Error Rate with continuous transmission from tower
QS* Bit Error Rate with discontinuous transmission from tower

BER (bit error rate) table
QF/QS register: 0 1 2 3 4 5 6 7
% of bit sent: 0.2 0.8 0.4 1.6 3.2 6.4 12.8 25.6
Siemens S6/S10

In Phonebook, store as your own number: +12022243121
Then you get the sun and two palms in the display, also a greeting message of the “MMI-team”.
It has been said that the phone number is the number of the Capitol building in Washington, DC (but not sure).
Siemens S15 Secret Menu’s

Press * -> # -> 7 -> 4 -> 3 -> 6 -> 3 -> 6 -> 7 -> * -> 8 -> 3 ->
7 -> 8 -> # ,press clear key to clear screen and return to
stand-by mode
press Menu, it will show additional menu
Menu 3.3.4 Band selection,
Menu 3.3.4.1 Automatic band selection,
Menu 3.3.4.2 select GSM 900 only,
Menu 3.3.4.3 select GSM 1800 only,

Menu 10 Engineering,
Menu 10.1 MS info,

Menu 10.2 software detail,
Menu 10.2.1 software version,
Menu 10.2.2 EEPROM version,

Menu 10.3 Test/production details
Menu 10.3.1 Hardware deta
Menu 10.3.2 production deta
Menu 10.3.3 Service deta
Menu 10.3.4 Mechanical deta

Menu 10.1.1 MS info on, then on the screen show these, for example:

FCN RXL C1 C2
642 011+11+91 -> PAGE 1

CID DSC CB
11211 045 000 -> PAGE 2

BCC NCC TN
000 002 00 -> PAGE 3

RXf RXs RQf RQs
00 00 00 00 -> PAGE 4

ATa APa Hn Hf
001 000 05 00 -> PAGE 5

DTU DTD HP CI
+ ? - - -> PAGE 6

MM CC RR
IdNS Nul Idl -> PAGE 7

## LG SECRET CODES

LG SECRET CODES

LG all models test mode: Type 2945#*# on the main screen.

2945*#01*# Secret menu for LG

IMEI (ALL): *#06#

IMEI and SW (LG 510): *#07#

Software version (LG B1200): *8375#

Recount cheksum (LG B1200): *6861#

Factory test (B1200): #PWR 668

Simlock menu (LG B1200): 1945#*5101#

Simlock menu (LG 510W, 5200): 2945#*5101#

Simlock menu (LG 7020, 7010): 2945#*70001#

Simlock menu (LG 500, 600): 2947#*

LG-U81XX SPECIAL CODES

Code to read phone version :

- Phone without SIM

- Enter 277634#*# or 47328545454#

- Select ‘SW Ver.info’

Code to reset phone :

- Phone without SIM

- Enter 277634#*# or 47328545454#

- Select ‘Factory Reset’

Code to enter UNLOCK MENU :

- Phone wit SIM inside

- Enter 2945#*88110#

Test Menu 8330 : 637664#*#

Test Menu 8180 V10a: 49857465454#

Test Menu 8180 V11a: 492662464663#

Test Menu 8130-8138: 47328545454#

Test Menu 8110-8120: 277634#*#

## SAMSUNG SECRET CODES

SAMSUNG SECRET CODES

Software version: *#9999#

IMEI number: *#06#

Serial number: *#0001#

Battery status- Memory capacity : *#9998*246#

Debug screen: *#9998*324# - *#8999*324#

LCD kontrast: *#9998*523#

Vibration test: *#9998*842# - *#8999*842#

Alarm beeper - Ringtone test : *#9998*289# - *#8999*289#

Smiley: *#9125#

Software version: *#0837#

Display contrast: *#0523# - *#8999*523#

Battery info: *#0228# or *#8999*228#

Display storage capacity: *#8999*636#

Display SIM card information: *#8999*778#

Show date and alarm clock: *#8999*782#

The display during warning: *#8999*786#

Samsung hardware version: *#8999*837#

Show network information: *#8999*638#

Display received channel number and received intensity: *#8999*9266#

*#1111# S/W Version

*#1234# Firmware Version

*#2222# H/W Version

*#8999*8376263# All Versions Together

*#8999*8378# Test Menu

*#4777*8665# GPSR Tool

*#8999*523# LCD Brightness

*#8999*377# Error LOG Menu

*#8999*327# EEP Menu

*#8999*667# Debug Mode

*#92782# PhoneModel (Wap)

#*5737425# JAVA Mode

*#2255# Call List

*#232337# Bluetooth MAC Adress

*#5282837# Java Version

Type in *#0000# on a Samsung A300 to reset the language

Master reset(unlock) #*7337# (for the new samsungs E700 x600 but not E710)

Samsung E700 type *#2255# to show secret call log (not tested)

Samsung A300, A800 phone unlock enter this *2767*637#

Samsung V200, S100, S300 phone unlock : *2767*782257378#

MOtorola Secret codes:

MOtorola codes:

IMEI number:
*#06#

Code to lock keys. Press together *7

Note: [] (pause) means the * key held in until box appears.

Select phone line - (use this to write things below the provider name):
[] [] [] 0 0 8 [] 1 []

Add phonebook to main menu:
[] [] [] 1 0 5 [] 1 []

Add messages to main menu:
[] [] [] 1 0 7 [] 1 []

Copy SIM memory (phonebook menu):
[] [] [] 1 0 8 [] 1 []

Eng Field options (main menu):
[] [] [] 1 1 3 [] 1 []

Slow (Frequency of search menu):
[] [] [] 1 0 1 [] 1 []

Medium (Frequency of search menu):
[] [] [] 1 0 2 [] 1 []

Fast (Frequency of search menu):
[] [] [] 1 0 3 [] 1 []

Enable EFR:
[] [] [] 1 1 9 [] 1 []

Function :
[] [] [] # # # [] 1 []

Change pin:
[] [] [] 0 0 4 [] 1 []

Unblocking using the “puk” number:
[] [] [] 0 0 5 [] 1 []

There are lots of similar codes exist. If you change the last number to 0 you can deactive that code. The 3 digit number at the middle are from 0 to 999. I put the most interesting codes. (EFR):Enhanced Full Rate Codec.

You can change GSM frequencies to 900/1800 by entering the enginnering model. Following the below steps:

enter menu and press 048263* quickly, then you will enter the secret engineering menu

under “Opcode”

input 10*0*3 for GSM 900

10*0*4 for GSM 1800

10*0*5 for GSM 1900

10*0*6 for dual band GSM 900/1800

10*0*7 for dual band GSM 850/1900

To add extra message space 4 your Motorola C350 C450 C550 or C650, press menu button, press 048263* quickly, then on the popup menu enter 47 press ok.press 50 and ok.press 1 ok.press 64 ok.press 1 ok.press 186 and ok.You will receive an extra 50 msgs memory space.Switch phone off and back on.(not tested)



IMEI number:
*#06#

Code to lock keys. Press together *7

Note: [] (pause) means the * key held in until box appears.

Select phone line - (use this to write things below the provider name):
[] [] [] 0 0 8 [] 1 []

Add phonebook to main menu:
[] [] [] 1 0 5 [] 1 []

Add messages to main menu:
[] [] [] 1 0 7 [] 1 []

Copy SIM memory (phonebook menu):
[] [] [] 1 0 8 [] 1 []

Eng Field options (main menu):
[] [] [] 1 1 3 [] 1 []

Slow (Frequency of search menu):
[] [] [] 1 0 1 [] 1 []

Medium (Frequency of search menu):
[] [] [] 1 0 2 [] 1 []

Fast (Frequency of search menu):
[] [] [] 1 0 3 [] 1 []

Enable EFR:
[] [] [] 1 1 9 [] 1 []

Function :
[] [] [] # # # [] 1 []

Change pin:
[] [] [] 0 0 4 [] 1 []

Unblocking using the “puk” number:
[] [] [] 0 0 5 [] 1 []

There are lots of similar codes exist. If you change the last number to 0 you can deactive that code. The 3 digit number at the middle are from 0 to 999. I put the most interesting codes. (EFR):Enhanced Full Rate Codec.

You can change GSM frequencies to 900/1800 by entering the enginnering model. Following the below steps:

enter menu and press 048263* quickly, then you will enter the secret engineering menu

under “Opcode”

input 10*0*3 for GSM 900

10*0*4 for GSM 1800

10*0*5 for GSM 1900

10*0*6 for dual band GSM 900/1800

10*0*7 for dual band GSM 850/1900

To add extra message space 4 your Motorola C350 C450 C550 or C650, press menu button, press 048263* quickly, then on the popup menu enter 47 press ok.press 50 and ok.press 1 ok.press 64 ok.press 1 ok.press 186 and ok.You will receive an extra 50 msgs memory space.Switch phone off and back on.(not tested)

## Sony Ericsson Secret Codes

Sony Ericsson Secret Codes


Sony Ericsson Secret Menu: -> * <- <- * <- *

(-> means press joystick, arrow keys or jogdial to the right and <- means left.)

You’ll see phone model, software info, IMEI, configuration info, sim lock status, REAL time clock, total call time and text labels.

You can also test your phones services and hardware from this menu (main display, camera, LED/illumination, Flash LED, keyboard, earphone, speaker, microphone, radio and vibrator tests)

IMEI Number: *#06#

Lockstatus: <- * * <-

Shortcut to last dialed numbers: 0#

Shortcut to sim numbers: On main menu type a number and press #

If you change the language from default to any other language, then it may be difficult to switch to default language. The shortcut is very simple. Just press <> . <> stands for right arrow button or joystick.

## NOKIA SECRET CODES

NOKIA SECRET CODES

On the main screen type

*#06# for checking the IMEI (International Mobile Equipment Identity).

*#7780# reset to factory settings.

*#67705646# This will clear the LCD display(operator logo).

*#0000# To view software version.

*#2820# Bluetooth device address.

*#746025625# Sim clock allowed status.

*#62209526# - Display the MAC address of the WLAN adapter. This is available only in the newer devices that supports WLAN like N80

#pw+1234567890+1# Shows if sim have restrictions.

*#92702689# - takes you to a secret menu where you may find some of the information below:

1. Displays Serial Number.

2. Displays the Month and Year of Manufacture

3. Displays (if there) the date where the phone was purchased (MMYY)

4. Displays the date of the last repair - if found (0000)

5. Shows life timer of phone (time passes since last start)

*#3370# - Enhanced Full Rate Codec (EFR) activation. Increase signal strength, better signal reception. It also help if u want to use GPRS and the service is not responding or too slow. Phone battery will drain faster though.

*#3370* - (EFR) deactivation. Phone will automatically restart. Increase battery life by 30% because phone receives less signal from network.

*#4720# - Half Rate Codec activation.

*#4720* - Half Rate Codec deactivation. The phone will automatically restart

If you forgot wallet code for Nokia S60 phone, use this code reset: *#7370925538#
Note, your data in the wallet will be erased. Phone will ask you the lock code. Default lock code is: 12345

Press *#3925538# to delete the contents and code of wallet.

*#7328748263373738# resets security code.

Default security code is 12345

Unlock service provider: Insert sim, turn phone on and press vol up(arrow keys) for 3 seconds, should say pin code. Press C,then press * message should flash, press * again and 04*pin*pin*pin#

Change closed caller group (settings >security settings>user groups) to 00000 and ure phone will sound the message tone when you are near a radar speed trap. Setting it to 500 will cause your phone 2 set off security alarms at shop exits, gr8 for practical jokes! (works with some of the Nokia phones.)

Press and hold “0″ on the main screen to open wap browser.

WANT TO KNOW WHO IS INVISIBLE ON YAHOO MESSENGER?

WANT TO KNOW WHO IS INVISIBLE ON YAHOO MESSENGER?


Just follow the any of the below link and type the yahooid of your friend.click here:
http://yscan.info/
or
http://www.invisible-scanner.com/

## Make Frnds scare for VIRUS

Make Frnds scare for VIRUS


Open notepad and type this:

lol=msgbox ("Warning a virus has been detected on your PC. Press YES to format your hard disk now or press NO to format your hard disk after system reboot",20,"Warning")

Then save it as Virus.VBS

and go to the folder that contains it and open it if a window pops out saying a virus has been detected it's working. Press yes or no to close the window and put it in the startup folder of the victim's account.
On startup the window should appear.
Note: This does not harm your computer as it does not contain virus.

The Yes and no button does not do anything except closing the window. And you can edit the virus in the sentence: Warning a virus has detected on your PC to any kind of virus eg.Trojan Horse like this lol=msgbox ("Warning a Trojan horse has been detected on your PC. Press YES to format your hard disk now or press NO to format format your hard disk after system reboot",20,"Warning")

Oh in between make sure your victim does not panic and really reformat his harddisk. hahaha :) 35

## INSTALL WINDOWS XP ON YOUR PC : DO IT YOUR SELF

I WILL TELL YOU EVRYTHING STEP BY STEP . AFTER READING THIS YOU WILL NEVER CALL AN ENGINEER TO REPAIR YOUR COMPUTER AND WASTE YOUR MONEY . ITS VERY SIMPLE . ANYBODY CAN DO IT.

How to install or upgrade to Windows XP

This article describes how to install Windows XP. You may find it easier to follow the steps if you print this article first because at the time of your computer windows failure you can install windows easily by reading them step by step.

Before you start, you must have your Windows XP installation CD(bootable) and the product key available.Ask your friends or your neighbours. Windows easy to arrange and is free.

1. Back up all important information before you perform a clean installation of Windows XP. Save the backup to an external location, such as a CD or external hard disk.
2. Start your computer from the Windows XP CD. To do this, insert the Windows XP CD into your CD drive or DVD drive, and then restart your computer.
   
3. When you see the "Press any key to boot from CD" message, press any key to start the computer from the Windows XP CD.
4. At the Welcome to Setup screen, press ENTER to start Windows XP Setup.
5. Read the Microsoft Software License Terms, and then press F8.
6. Follow the instructions on the screen to select and format a partition where you want to install Windows XP.
7. Follow the instructions on the screen to complete the Windows XP Setup.

If you have successfully followed above easy steps, you are finished.
After finishing this installation now you have to install windows drivers that you already got a DRIVERS-CD when you purchased your computer.OR if you dont have that CD just download the drivers for free from any of this link:-
http://www.driverfiles.net/Motherboards/page,level1,ID26.html
or
http://www.hardwaresecrets.com/page/drivers_motherboard



NOTE :YOU CAN ASK ANYTHING YOU WANT BY POSTING COMMENTS .

Provide feedback on this information..PLEASE GIVE COMMENTS

Did this information solve your problem?
What can we do to improve this information?
All question are welcomed here. We will do our best to give you the best solutions.